ARMY TM 5-6675-238-14
MARINE CORPS TM 08839A-14/1
8-34. Capacitor C1 or C2 Removal and Replacement.
See figure 8-10, sheet 2, and remove and replace capaci-
tor C1 (111) as follows:
a. Removal.
(1) Remove two screws (112) and lockwashers
(113) securing two terminal lugs (114) to ca-
pacitor Cl (111) terminals; tag and remove
terminal lugs.
(2) Loosen four screws (121) securing clamp (110)
around capacitor C1; remove capacitor C1
from clamp.
b. Replacement.
(1) Install capacitor Cl (111) in clamp (110).
(2) Tighten four screws (121) to secure clamp
around capacitor CL
(3) Secure two terminal lugs (114) to capacitor
Cl terminals with two screws (112) and lock-
washers (113). Orange wire connects to posi-
tive terminal of capacitor C1.
8-35. Filter FL1 or FL2 Removal and Replacement.
See figure 8-10, sheet 2, and remove and replace filter
FL2 (52) as follows:
a. Removal.
(1)
(2)
(3)
Remove two screws (47, figure 8-10, sheet 1)
and washers (46) securing cover (45) on rear of
motor B3 (17).
Carefully hold red and black motor B3 input
leads while pushing cover back from motor
B3. This compresses the braided shielding
slightly and provides extra lead length.
Carefully slide sleeving on each wire toward
rear cover for access to-solder connection. Tag
and unsolder wires from motor B3.
NOTE
The following two steps apply only to
filter FL2.
(4) Remove photocell amplifier A1 (57, figure
8-10, sheet 2) and pulse rate generator and
logic A2 (58).
(5) Remove three nuts (103), washers (102), and
lockwashers (101), and two screws (29, figure
8-10, sheet 1), nuts (20), lockwashers (21), and
washers (22) securing frame to front panel and
card cage. Move frame aside to gain access to
filter FL2 (52, figure 8-10, sheet 2) hardware.
NOTE
The following step applies only to filter
FL1.
(6) Remove servo amplifier A6 (63) to gain access
to filter FL1 (64) hardware.
(7) Remove two nuts (55), lockwashers (54), wash-
ers (53), and one terminal lug (56) securing
filter FL2 (52) to front panel; remove filter
FL2.
b. Replacement.
(1) Secure filter FL2 (52) to front panel with two
washers (53), lockwashers (54), nuts (55), and
one terminal lug (56).
(2) Place sleeving on wires that connect to motor
B3 (17, figure 8-10, sheet 1).
(3) Solder wires to terminals on rear of motor B3.
Slide sleeving over solder connections.
(4) Secure cover (45) to rear of motor B3 with
two screws (47) and washers (46).
NOTE
The following step applies only to filter
FL1.
(5) Replace servo amplifier A6 (63, figure 8-10,
NOTE
The following two steps apply only to
filter FL2.
(6) Secure frame to front panel and card cage
with two screws (29, figure 8-10, sheet 1), nuts
(20), lockwashers (21), and washers (22), and
three nuts (103, figure 8-10, sheet 2), washers
(102), and lockwashers (101).
(7) Replace photocell amplifier A1 (57) and pulse
rate generator and logic A2 (58).
8-36. Terminal Board TB1 Removal and Replacement.
See figure 8-10, sheet 2, and remove and replace termi-
nal board TB1 (87) as follows:
a. Removal.
(1) Tag and unsolder wires from terminal board
(2) Remove two screws (93), lockwasher (94) and
washer (95) securing terminal board TB1 (87)
and insulator (86) to chassis; remove terminal
board and insulator.
b. Replacement.
(1) Secure terminal board TB1 (87) and insulator
(86) to chassis with two screws (93), lockwash-
ers (94) and washers (95).
8-103