ARMY TM 5-6675-238-14
MARINE CORPS TM 08839A-14/1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Remove four screws (4), two screws (5), and
two washers (6) securing cover (7) to front
panel (28) and chassis (72) ; remove cover.
Disconnect connector P2 (47) from connector
P1 (48, figure 8-10.1, sheet 2).
Disconnect connector P3 (40) from power
supply (51, figure 8-10.1, sheet 1).
Disconnect left and right spooler motor cables
)
from power supply (51 .
Remove two screws (24) and washers (25)
securing front panel (28) to two posts.
Remove 11 screws (26) and washers (27) secur-
ing front panel (28) to chassis (72).
Carefully move front panel (28) away from
chassis (72) just far enough to disengage power
supply (51) connector and tape reader module
(46) connector from logic board (38, figure
8-10.1, sheet 2) connectors.
Remove two screws (49, figure 8-10.1, sheet 1)
and washers (50) securing power supply (51) to
front panel (28); remove power supply.
b. Replacement.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Secure power supply (51) to front panel (28)
)
with two screws (49) and washers (50 .
Carefully move front panel (28) toward chassis
(72) to engage power supply (51) connector
and tape reader module (46) connector with
logic board (38, figure 8-10.1, sheet 2) connec-
tors.
Secure front panel (28, figure 8-10.1, sheet 1)
to chassis (72) with 11 screws (26) and washers
(27).
Secure front panel (28) to posts with two
screws (24) and washers (25).
Connect left and right spooler motor cables to
power supply (51),
Connect connector P3 (40, figure 8-10.1, sheet
1) to power supply (51, figure 8-10.1).
Connect connectors P2 (47) to connector P1
(48, figure 8-10.1, sheet 2).
Secure cover (7, figure 8-10.1, sheet 1) to front
panel (28) and chassis (72) with four screws
(4), two screws (5), and two washers (6).
8-43.8. Left Spooler Motor B1 or Right Spooler Motor
B2 Removal and Replacement. See figure 8-10.1, sheet
1, and remove right spooler motor B2 (54) as follows:
a. Removal.
(1)
(2)
(3)
Remove four screws (4), two screws (5), and
two washers (6) securing cover (7) to chassis
(72); remove cover.
Disconnect right spooler motor B2 (54) cable
from power supply (51).
Remove four screws (52) and washers (53)
securing right spooler motor B2 (54) to front
panel (28); remove right spooler motor B2.
b. Replacement.
(1) Secure right spooler motor B2 (54) to front
panel (28) with four screws (52) and washers
(53).
(2) Connect right spooler motor B2 (54) cable to
power supply (51).
(3) Secure cover (7) to front panel (28) and chassis
(72) with four screws (4), two screws (5), and
two washers (6).
8-43.9. Time Totalizing Meter M1 Removal and Re-
placement. See figure 8-10.1, sheet 1, and remove time
totalizing meter Ml (58) as follows:
a. Removal.
(1) Remove four screws (4), two screws (5), and
two washers (6) securing cover (7) to front
panel (28) and chassis (72) ; remove cover.
(2) Tag and disconnect wires from time totalizing
meter Ml (58).
(3) Remove two screws (56) and nuts (57) securing
time totalizing meter M1 (58) to front panel
(28); remove time totalizing meter Ml.
b. Replacement.
(1) Secure time totalizing meter M1 (58) to front
panel (28) with two screws (56) and nuts (57).
(2) Connect wires to time totalizing meter M1
(58); remove tags.
(3) Secure cover (7) to front panel (28) and chassis
(72) with four screws (4), two screws (5), and
two washers (6).
8-43.10. Connector J1 and I/O Cable Removal and
Replacement. See figure 8-10.1, sheet 1 and remove and
replace connector J1 and I/O cable (61) as follows:
a. Removal.
(1) Remove four screws (4), two screws (5), and
two washers (6) securing cover (7) to front
panel (28) and chassis (72) ; remove cover.
(2) Tag and disconnect I/0 cable wires from filter
FL1 (71, figure 8-10.1, sheet 2), fuseholders
XF1 and XF2 (62 and 63, figure 8-10.1, sheet
1), and time totalizing meter Ml (58).
8-104.6
Change 1
